AGV Drive System Selection Guide: Dynamic Calculation Method for Drive Wheels, Low Voltage Servo Motors and Servo Drives


Release time:

2026-07-02

Preface

The operational performance of AGVs (Automated Guided Vehicles) and AMRs (Autonomous Mobile Robots) largely depends on whether the drive system is properly designed.

In a complete mobile robot drive architecture, the AGV drive wheel provides traction force, the low voltage servo motor delivers torque output, the gearbox performs torque amplification, and the servo drive ensures precise motion control. Together, these four components determine acceleration capability, climbing performance, positioning accuracy, and long-term operational reliability.

In practical engineering applications, many drive system issues are not caused by insufficient motor performance, but by incomplete vehicle dynamics calculations. A common mistake is selecting motors based solely on rated payload without considering rolling resistance, slope resistance, acceleration inertia, and wheel-ground adhesion. This often leads to startup failure, motor overload, wheel slippage, or reduced system efficiency.

As an early developer in mobile robot drive systems, Yikong Intelligent has long been focusing on AGV drive wheels, differential drive systems, low voltage servo motors, servo drives, and integrated motion solutions. Based on engineering practice and mechanical design principles, this article systematically explains the dynamic calculation methodology for AGV drive systems, providing a reference for system design and selection.


1. AGV Vehicle Driving Resistance Analysis

For industrial AGVs operating at speeds typically below 1 m/s, air resistance can be neglected. Therefore, the total driving force must overcome three main resistances:

  • Rolling resistance
  • Slope resistance
  • Acceleration inertia resistance

The basic force balance is:

Fdrive ≥ Ff + Fθ + Fa

Where:

SymbolDescription
FdriveTotal traction force (N)
FfRolling resistance (N)
FθSlope resistance (N)
FaAcceleration inertia force (N)

Only when the driving force exceeds the total resistance can stable motion be ensured.


2. Rolling Resistance Calculation

Rolling resistance is generated by elastic deformation between the wheel and the ground and is the most fundamental resistance during continuous motion.

Formula:

Ff = (f × G) / r

Where:

ParameterDescriptionUnit
FfRolling resistanceN
fRolling resistance coefficientm
GVehicle weightN
rWheel radiusm

Typical Engineering Values:

Wheel & Surface Conditionf Value
Polyurethane wheel + epoxy floor0.0018–0.0025
Polyurethane wheel + concrete floor0.0020–0.0030
Steel wheel systems0.0010–0.0015

Engineering Note:
Some reference materials still define rolling resistance coefficient in centimeters (cm). It must be converted into meters (m) during calculation, otherwise the result may deviate by up to 100×.


3. Slope Resistance Calculation

Industrial AGVs are typically designed for a 2% slope capability.

For small angles:

sinθ ≈ tanθ ≈ slope ratio

Therefore:

Fθ = 0.02 × G

Example:

For a 500 kg AGV:

G = 500 × 9.81 = 4905 N

Fθ ≈ 98.1 N

For larger slopes, trigonometric functions should be used for higher accuracy.


4. Acceleration Inertia Resistance

Frequent start-stop operation introduces significant inertial loads.

Formula:

Fa = M × a

Where:

ParameterDescription
MVehicle mass (kg)
aAcceleration (m/s²)

Recommended Design Values:

ApplicationAcceleration
Standard logistics AGV0.4–0.6 m/s²
Human-robot collaboration0.2–0.3 m/s²
Heavy-duty AGV≤ 0.2 m/s²

Higher acceleration improves responsiveness but increases peak load on the drive system.


5. Total Resistance Calculation Example

5.1 Design Parameters

ItemValue
Vehicle mass500 kg
Wheel radius65 mm
Rolling coefficient0.002
Slope2%
Acceleration0.5 m/s²

5.2 Calculation Results

Resistance TypeResult
Vehicle weight G4905 N
Rolling resistance Ff150.92 N
Slope resistance Fθ98.10 N
Acceleration resistance Fa250 N
Total resistance ΣF499.02 N

5.3 Design Conclusion

The maximum required traction force is approximately:

499 N

For engineering design, a safety margin of 20%–50% is recommended to account for startup shock, ground variation, and long-term operational losses.

Engineering Insight:
Drive system failures rarely occur under steady-state conditions. Most failures happen during transient states such as startup, slope climbing, and acceleration peaks. Therefore, peak resistance must always be used for system sizing.


6. Drive Wheel Torque Calculation

The output torque is generated by the low voltage servo motor through a gearbox.

Formula:

Twheel = Tm × i × η

Where:

ParameterDescription
TwheelOutput torque (Nm)
TmMotor rated torque
iGear ratio
ηGear efficiency

Typical efficiencies:

  • Planetary gearbox: ~0.85
  • Worm gearbox: 0.60–0.70

Different gearbox types must not be mixed using the same efficiency assumptions.


7. Traction Force Calculation

Torque is converted into traction force:

F = T / r

For dual-drive systems:

Ftotal = 2 × F

Example:

  • Motor torque: 0.4 Nm
  • Gear ratio: 30
  • Efficiency: 0.85
  • Wheel radius: 65 mm

Output torque ≈ 10.2 Nm
Single wheel traction force ≈ 157 N

This value directly determines whether the AGV can overcome system resistance.


8. Maximum Speed Calculation

Theoretical speed is determined by motor speed and gear ratio:

V = (2 × π × r × n) ÷ i

Where n is motor speed (rpm).

Example:

  • 2500 rpm
  • Gear ratio: 30
  • Wheel radius: 65 mm

Theoretical speed ≈ 34 m/min (≈ 0.57 m/s)

Speed and torque must always be balanced during system design.


9. Motor Power Verification

Formula:

P = (T × n) / 9550

Example result:

≈ 0.105 kW

Engineering Recommendation:

  • Torque safety margin: 1.2–1.5×
  • Power margin: 20%–50%

10. Wheel Adhesion and Preload Force

To prevent wheel slippage:

μ × FN ≥ F

Therefore:

FN ≥ F / μ

Example:

  • Single wheel force: 157 N
  • Friction coefficient: 0.54

Required preload force ≈ 291 N

Recommended spring preload: ~320 N (including fatigue margin)


Typical Surface Friction Coefficients:

Surfaceμ
Dry epoxy floor0.75
Wet concrete0.35
Dry gravel0.65
Dry soil0.54
Wet surface0.30
Ice/snow0.25

11. AGV Drive System Selection Workflow

  1. Define vehicle mass, speed, acceleration, slope
  2. Calculate rolling, slope, and acceleration resistance
  3. Determine total traction force
  4. Calculate single wheel load
  5. Derive required output torque
  6. Select gearbox ratio
  7. Match low voltage servo motor
  8. Verify servo drive capacity
  9. Check speed performance
  10. Verify adhesion and preload force

12. Engineering Considerations

  • Rolling resistance coefficient and friction coefficient are fundamentally different parameters and must not be confused.
  • Gearbox efficiency varies significantly depending on structure.
  • Motor and servo drive selection must consider continuous duty cycles and peak loads.
  • Multi-wheel systems must ensure sufficient ground contact force to avoid slippage and positioning deviation.

Conclusion

AGV drive system design is not only motor selection, but a comprehensive engineering process involving vehicle dynamics, mechanical transmission, electrical control, and system integration.

From resistance modeling to torque calculation, and from servo motor selection to gearbox and drive wheel design, every parameter directly affects system performance and reliability.

Return to List →

力星 +86-15989586580

Mob‌: +86-513-82104870

E-mail: jimmy.tang@shtongpu.com

E-mail: info@bicontrols.com
Address: Building 63, No.2699, Binjiang Street, Binjiang Avenue, Haimen District, Nantong City, Jiangsu Province

YIKONG

Sweep and pay attention to Baoyan Technology

Business License